PROCESS INSTRUMENTATION


ACCESSORIES

The PCU-10 permits the operation of up to 10 flow meters or flow controllers of the red-y smart series with predefined process recipes.

  • Display of the gas flow set value for each connected meter and controller
  • Display of the gas flow actual value for each connected meter and controller
  • Specification and storage of set values
  • Storage of up to 12 different gas mixtures as recipes
  • Total flow meter for each connected meter and controller
  • Specification of minimum and maximum limit values with red alarm display on reaching the limits
  • Gas mixer with up to 12 recipes
  • Display of the instrument temperature of the connected meter and controller
  • Mixed operation with Vögtlin and BHT devices possible
  • No additional mains adaptor required
  • Control of the connected meter and controller with a PC by means of PDM-U connection cable
  • Use of the Vögtlin  get red-y  software on a PC for direct configuration of the meter and controller

Communication Cable

  • Communication cable PC/red-y galvanically separated
  • Active level converter USB/RS485
  • Powered by power supply PSD

PSD – PLUG -Type Power Supply (1.8m)

  • Input: 100 – 240Vac, 50 – 60Hz
  • Output: 24Vdc, approx. 0.5A (12W)
  • connector with locking ring, dia. 2.1/5.5mm

RED-Y COMPACT

Battery Powered Digital Mass Flow Meters with optional Needle Valve

  • AA battery powered device with touch display
  • MEMS sensor technology
  • Customer-specific flow units
  • Use as a meter, regulator or switch
  • Measuring ranges from 25 mln/min up to 450 ln/min (27 SCCM – 480 SLPM)
  • Turndown ratio  1:100
  • Accuracy, ± 1.0% of full scale up to 50 ln/min (50 SLPM)
  • Repeatability ± 0.5% of full scale
  • Response time Max. 300 msec 
  • Operating pressure 0.2 – 11 bara (3 – 160 psia)
  • Operating temperature 0 – 50°C (32 – 122°F)
  • Body material, Anodized aluminium, optional stainless steel electro polished
  • Warm-up-Time, < 1 sec. for full accuracy
  • Display, ouch display (128×64 px) with automatic position adjustment (position sensor)
  • IP Class IP50
  • Leak Rate < 1 x 10-6 mbar l/s He
  • Test Pressure 16 bara (240 psia)
  • No output signal.

RED-Y ATEX

Thermal Mass Flow Meters and Controllers with IP67 & Ex Protection

  • Accurate & fast measurement/control
  • Analog and digital interface
  • IP67/NEMA6 and ATEX rating
  • Options: Multigas (up to 10 gases), Profibus
  • Measuring ranges from 25 mln/min up to 450 ln/min (27 SCCM – 480 SLPM)
  • Accuracy: ± 0.3% of full scale + ± 0.5% of reading
  • Turndown ratio: 1 : 100
  • Repeatability, ± 0.2% of full scale 
  • Power supply, 24 Vdc (18 – 30 Vdc), 15 Vdc on request
  • Operating pressure, 0.2 – 11 bara (3 – 160 psia) 
  • Body material, Stainless steel 316L
  • Output analog signal, 0-20 mA, 4-20 mA, 0-5 V, 1-5 V, 0-10 V, 2-10 V
  • Output digital signal, RS-485; Modbus RTU / option: Profibus
  • IP Class IP67
  • Leak Rate < 1 x 10-6 mbar l/s He
  • Test Pressure 16 bara (240 psia)
  • ATEX Cerification, II 3G nA IIC T4 Gc (Category 3/Zone 2)
  • II 3D Ex tc IIIC T100°C Dc (Category 3/Zone 22)

Q-FLOW

Q-Flow is a modern VA-flowmeter for gases built on the variable area principle.

  • Measuring tubes in 80mm and 140mm sizes
  • Measuring ranges from 0.06 ln/min up to 50 ln/min for Air @ 1013 mbar abs / 20°C
  • Maximum pressure: 10 bar / Maximum temperature: 100°C
  • The bodies are available in aluminium. Sealing material FKM.
    Body in stainless steel 1.4305 and sealing materials EPDM or FFKM on request.
  • Operating temperature 0 100deg c
  • Standard setup with valve at inlet
  • Leak Rate better than 1 x 10-5 mbar l/s He

M-FLOW

M-Flow  micro needle valves were developed for fine dosages of gases and liquids.

  • Body Material: Anodized aluminium or stainless steel
  • Operating temperature:  -40 °C to 100 °C
  • Operating pressure: 40bar
  • Leak rate : < 1 x 10-5 mbar l/s He
  • Digiturn with display with 100 divisions

GAS MIXING SYSTEM

Precise measurement and stable regulation of behaviour are important if the quality of gas mixtures is to be maintained at a high level.

  • The control speed of less than 500 ms.
  • Very accurate and fast regulation
  • High repeatability
  • Calibration with the actual gas
  • High savings possible with mixed gases
  • Independent of temperature and pressure
  • Easy maintaining and service

RED-Y SMART

High-precision Reliable and accurate Mass Flow Meters and Controllers (MFC) for Gases

  • High-precision measurement
  • Analog and digital interface
  • Safe and fast control
  • Options: Multigas (up to 10 gases), Profibus, built-in display
  • Measuring ranges from 25 mln/min up to 450 ln/min (27 SCCM – 480 SLPM)
  • Operating pressure 0.2 – 11 bar a (3 – 160 psia)
  • Operating temperature 0 – 50°C (32 – 122°F)
  • Accuracy: ± 0.3% of full scale + ± 0.5% of reading
  • Turndown ratio: 1 : 100
  • Repeatability ± 0.2% of full scale
  • Body material, Anodized aluminum, optional stainless steel electro polished
  • Warm-up-time, < 1 sec. for full accuracy
  • IP Class IP50
  • Leak Rate < 1 x 10-6 mbar l/s He
  • Test Pressure 16 bara (240 psia)
  • Output signal analog, 0-20 mA, 4-20 mA, 0-5 V, 1-5 V, 0-10 V, 2-10 V
  • Output signal digital, RS-485; Modbus RTU Option: Profibus DP-V0, DP-V1 / Profinet RT/EtherCAT
 
     
86067 visits